This authentically reproduced brace features all of the factory drainage holes as well as the correct flanges for a straightforward installation. Stamped from heavy-gauge steel, the brace fits at the rearmost section of the body, below the trunk pan and...

new detailed reproduction rear cross member located at the back of the car between frame. applications: 1968-1972 chevelle & malibu 1968-1972 gto / lemans / tempest 1968-1972 skylark 1968-1972 cutlass 1970-1972 monte carlo

Welded to the underside of the trunk floor behind the rear bumper, the last two body mounts to attach here. Does not fit El Camino or other wagon models, this is for 2 door and 4 door models. applications: 1968-1969 Chevy Chevelle & Malibu

Welded to the underside of the trunk floor behind the rear bumper, the last two body mounts to attach here. For all models except wagon applications: 1970 Chevelle & Malibu

Welded to the underside of the trunk floor behind the rear bumper, the last two body mounts to attach here. For all models except wagon applications: 1971-1972 Chevelle & Malibu

New rear inner valance panel/cross rail.  mounts behind tail light panel. holes are cut for back-up lights. applications: 1967-1968 Camaro Rally Sport

Rear inner valance panel/cross rail, mounts behind tail light panel. Holes are not cut for RS back-up lights. applications: 1967-1968 Camaro (non rally sport) 1967-1968 Firebird

one of our best selling items, this piece fits behind the tail light panel and is almost always rusted or bent.  if you're repairing a tail light panel or replacing a trunk floor you will need this item. applications: 1969 camaro 1969 firebird

almost always rusted or damaged, this rear crossmember attaches to the lower backside of the tail light panel and the back edge of the trunk floor. this piece is essential when you are repairing or replacing panels at the rear most section of the car.new...

almost always rusted or damaged, this rear cross member attaches to the lower backside of the tail light panel and the back edge of the trunk floor. this piece is essential when you are repairing or replacing panels at the rear most section of the car...

new reproduction rear crossmember located under the back edge of the trunk floor. this is the last location on the car for mounting the body cushionsfits: 1949-52 chevy all models

This new cross member is located at the back edge of the trunk floor panel on the underside.Fits all models except wagon applications: 1953-1954 Chevy Bel Air

New reproduction of the original, welds to underside of trunk floor at rear of body, fits all body styles except wagons and Nomads. applications: 1955-1957 Chevy Bel Air

This exact as original replacement brace for 1962 full size models except wagons mounts under the trunk floor at the rear section. built to original specifications with heavy gauge steel that meets or beats oem quality. NOTE: WILL NOT FIT 1961 MODELS!...

This exact as original replacement brace for 1963 full size models except wagons mounts under the trunk floor at the rear section. built to original specifications with heavy gauge steel that meets or beats oem quality. applications: 1963 Impala 1963 Bel...

the rear cross member that welds to the back end of the frame rails.  it's usually rusted and often bent from towing another car, correct gauge steel as original.  it's much easier to weld in our new oe style brace than to repair your old one...

this replacement brace for all 1965 full size models mounts under the trunk floor at the rear section. built to original specifications with heavy gauge steel that meets or beats oem quality. applications: 1965 Impala 1965 Bel Air  

This replacement brace for all 1965-66 full size models except wagons mounts under the trunk floor at the rear section. Built to original specifications with heavy gauge steel that meets or beats oem quality. applications: 1966 Impala 1966 Bel Air 1966...

New steel (not aluminum) edp coated reinforcement supports the rear bumper and then attaches to the rear bumper brackets as one unit. applications: 1981-1987 Buick Regal

This brace is located at the rear of the trunk floor, the rear body mounts bolt to it and the rear gas tank strap bolts slide into this rail as well. Note: caged nuts are not included. applications: 1964-1967 GTO / Lemans / Tempest  

This authentically reproduced brace features all of the factory drainage holes as well as the correct flanges for a straightforward installation. Stamped from heavy-gauge steel, the brace fits at the rearmost section of the body, below the trunk pan and...

Our product is properly factory gauged and properly die formed with all captured nuts. We have paid very close attention to quality and detail and thus have an exceptional product for you. applications: 1976-1985 Jeep CJ7

This is a high quality reproduction of the original cross member, die stamped and properly reinforced. If you are repairing rear shackle mounts then this premium cross member will tie it all together. Factory installed rubber mounts between the body and...

This is a die-stamped, galvanized, reproduction of the rear splash shield. This attaches to the forward part of the rear cross sill applications: 1987-1995 Jeep YJ Wrangler

Tailgate end supports attach to the body and to the frame with a body bolt at each end of the support.  Our product is properly factory gauged and properly die formed with all captured nuts. We have paid very close attention to quality and detail...

This is a high quality reproduction of the original cross member, die stamped and properly reinforced. If you are repairing rear shackle mounts this premium cross member will tie it all together. Factory installed rubber mounts between the body and the...

rear cross member extension for the 1968-1970 dodge & plymouth b-body models, except charger. stamped from high quality heavy gauge steel, this product mounts to the end of the rear cross member and mates to the back of the trunk extension...

rear cross member extension for the 1968-1970 dodge & plymouth b-body models, except charger. stamped from high quality heavy gauge steel, this product mounts to the end of the rear cross member and mates to the back of the trunk extension...

connects the the main center rear cross member and blocks off the backside of the trunk floor extension.fits: 1970-74 challengerfits: 1970-74 barracuda

connects the the main center rear cross member and blocks off the backside of the trunk floor extension.fits: 1970-74 challengerfits: 1970-74 barracuda

This bracket is attached to both the front and rear section of the rear cross member assembly. die formed and edp coated. applications: 1968-1972 Chevy II & Nova  

This bracket is attached to both the front and rear section of the rear cross member assembly. die formed and edp coated. applications: 1968-1972 Chevy II & Nova

heavy steel gauge like original. use when replacing center cross member. applications: 1970-1973 camaro

heavy steel gauge like original. use when replacing center cross member. applications: 1970-1973 camaro

New reproduction with nylon spacer included. applications: 1968-1972 Elcamino

New edp coated reproduction of the originals for 2 door and 4 door sedans. includes hinge box, hinge arms & pins and torsion bar brackets. right hinge assembly includes forward upper jack stowage bracket. applications: 1955-1957 Chevy Sedan  

new edp coated reproduction of the originals applications: 1955-1957 chevy convertible

New edp coated reproduction of the originals applications: 1955-1957 Chevy 2 door hardtop

New inner lower rear brace that is part of the outer wheelhouse and welded to the bedside patch. Lh= driver side applications: 1973-1986 chevy & gmc pickup c/k series 1987-1991 chevy & gmc pickup r/v series 1973-1991 blazer & jimmy The...

New inner lower rear brace that is part of the outer wheelhouse and welded to the bedside patch. Rh= passenger side applications: 1973-1986 chevy & gmc pickup c/k series 1987-1991 chevy & gmc pickup r/v series 1973-1991 blazer & jimmy The...

Reproductions Of Original Fits 2-Door Hardtop & Convertible Only applications: 1955-1957 Chevy

New pre-molded and pre-drilled gas tank strap, 1 required per car. Fits 2 door and 4 door models except wagons. applications: 1967 Barracuda 1967 Dart 1967 Valiant

fits: 1968-76 dartfits: 1973-76 dart sportfits: 1971-72 demonfits: 1968-69 barracudafits: 1970-76 duster

applications: 1962-1965 330 / 440 / coronet 1962 Dart 1962-1965 belvedere 1965 satellite 1962-1964 savoy 1962-1964 fury 1962-1964 polara

applications 1963-1966 dodge dart 1964-1966 barracuda 1963-1966 valiant

use 1 per car. applications: 1966-1967 gtx / satellite / belvedere 1966-1967 charger 1966-1967 coronet

applications: 1968-1970 charger 1968-1970 coronet 1968-1970 roadrunner / gtx / satellite / belvedere

applications: 1971-1973 charger 1971-1973 roadrunner / gtx / satellite

 

This fuel tank strap set applications: 1978-1983 JEEP CJ5 1978-1986 JEEP CJ7 1987-1990 JEEP YJ Wrangler

new edp coated reproduction gas tank straps ready to bolt on. except wagons. applications: 1962-1967 chevy ii/nova

new edp coated reproduction gas tank straps ready to bolt on. fits: 1968-1972 nova fits: 1971-1972 ventura

New reproduction gas tank straps, fits 2 door and 4 door models, not for wagons. applications:1964-1967 Chevelle & Malibu 1964-1967 GTO / Lemans / Tempest 1964-1967 Cutlass 1965-1966 Chevy Impala/Bel Air 1964-1967 Skylark & Special

Sold as a pair fits all models except wagon and El camino. applications: 1968-1972 chevelle / malibu1968-1972 gto / lemans / tempest1968-1972 cutlass / 4421968-1972 skylark1970-1972 monte carlo

Fits 2 door and 4 door models except wagons. applications: 1973-1977 Chevelle / Malibu / Laguna 1973-1977 GTO / Lemans / Tempest 1973-1977 Cutlass 1973-1977 Monte Carlo

Pre-molded to fit like the originals, sold as a 2 piece set. applications: 1978-1988 Monte Carlo 1978-1983 Malibu 1978-1981 Lemans

new die stamped reproduction.fits: 1967-1969 camarofits: 1967-1969 firebird

fits: 1970-73 camarofits: 1970-73 firebird

fits: 1974-81 camarofits: 1974-81 firebird

applications: 1982-1992 Camaro/Z28 1982-1992 Firebird/Trans am

new reproduction setfits: 1964-67 el caminofits: 1964-67 chevelle wagon

new reproduction setfits: 1978-87 elcamino & cabellero

Reproduction Of Original Fits All Nomad, Station Wagon & Sedan Delivery. Includes Seal & Strainer. applications 1955-1957 Chevy Station Wagon, Nomad, Sedan Delivery

Reproduction Of Original Fits All Nomad, Station Wagon & Sedan Delivery. Includes Seal & Strainer. applications 1955-1957 Chevy Station Wagon, Nomad, Sedan Delivery

New edp coated pair of gas tank straps, hardware not included. Fits all 2 door and 4 door models except wagon. applications: 1961-1964 Impala 1961-1964 Bel Air 1961-1964 Biscayne

New machine formed gas tank straps for all models except Nomad and Wagons. Applications: 1955-1957 Chevy hardtop, convertible, & sedan 150, 210 & bel air (2 door & 4 door)

fits: 1955-57 chevy hardtop, convertible, & sedan 150, 210 & bel air 2 door & 4 door (except station wagon, sedan delivery & nomad)

applications: 1955-1957 chevy hardtop, convertible, & sedan 150, 210 & bel air(2 door & 4 door)

steel full replacement gas tank straps for mounting the original style gas tank under the bed. applications: 1947-1948 chevy & gmc pickup

steel full replacements sold as a pair applications: 1949-1955 chevy & gmc pickup (1st series)

Reproduction fuel tank straps for the 55-59 Chevrolet / GMC Truck. Made like OE. Each strap is stamped from high quality heavy gauge steel and features the correct shape, size, bends and holes. Sold as a pair. Hardware not included. Note: For use on 2nd...

applications: 1960-1966 chevy & gmc pickup

Sold as a kit for 1 gas tank on the driver side and 1 gas tank on the passenger side. Replace your Chevy & GMC trucks rusted or damaged gas tank straps and brackets with these factory correct replacement parts. The already riveted straps are for 16...

Reproduction gas tank front and rear support with straps for the 1973-1991 Chevy GMC C/K Squarebody trucks. These premium reproductions come with complete accommodations for installation including weld nuts pre-attached when mounting them to the frame,...

Replace your Chevy & GMC trucks rusted or damaged gas tank strap and bracket with this factory correct replacement part. The already riveted straps is for 16 or 20 gallon tanks, bracket and strap are for the rear of the drivers side or passenger side...

Replace your Chevy & GMC trucks rusted or damaged gas tank strap and bracket with this factory correct replacement part. The already riveted straps is for 16 or 20 gallon tanks, bracket and strap are for the front of the drivers side or passenger...

Note: These will be bent as shown, this is for shipping/packaging purposes and the straps will need to be straigtened for installation. This kit includes: Fuel tank straps (2) "J" bolts (2) applications: 1969-1972  Chevrolet Blazer 1970-1972 GMC...

New edp coated gas tank straps, manufactured to match the originals perfectly. applications: 1984-1996 JEEP XJ Cherokee  1984-1996 JEEP XJ Wagoneer

New die stamped and pre-formed gas tank strap set. applications: 1984-1990 Jeep Grand Wagoneer

Does not fit wagon models. applications: 1962-1965 330 / 440 / coronet1962-1965 belvedere 1965 satellite 1962-1964 savoy 1962-1964 fury 1962-1964 polara

Does not fit wagon models. applications: 1962-1965 330 / 440 / coronet1962-1965 belvedere 1965 satellite 1962-1964 savoy 1962-1964 fury 1962-1964 polara

fits: 1966-67 charger fits: 1966-67 belvedere / satellite / gtxfits: 1966-67 coronet*440 & hemi (3/8 in.)

fits: 1966-67 charger fits: 1966-67 belvedere / satellite / gtxfits: 1966-67 coronet*2 door, 4 door & wagon models

Use with Hemi or 440, includes return line. applications: 1968-1970 Charger 1968-1970 Roadrunner / Satellite / Gtx / Belvedere 1968-1970 Coronet

fits: 1968-70 charger fits: 1968-70 roadrunner / satellite / gtx / belvederefits: 1968-70 coronet(except wagon models)

For all big block models except wagons. 3/8 inch fuel line applications 1971-1973 Charger 1971-1973 Roadrunner / Satellite / GTX

Fits all models except wagons. applications: 1971-1973 Charger 1971-1973 Roadrunner / Satellite / GTX

New reproduction 3/8 inch fuel sending unit with return line for Chrysler big block. applications: 1970-1974 Barracuda 1970-1974 Challenger

New reproduction 5/16 fuel sending unit without return line for Chrysler small block. applications: 1970-1974 Barracuda 1970-1974 Challenger

fits: 1962-1965 chevy ii & nova

fits: 1962-1965 chevy ii & nova

fits: 1966-1967 chevy ii & nova

includes lock ring & gasket.fits: 1966-67 chevy ii & nova

fits: 1968-1972 chevy ii & nova fits: 1967-1969 camaro fits: 1967-1969 firebird

includes lock ring & gasket. 3/8 in. w/o return line.fits: 1968-1972 chevy novafits: 1967-1969 camarofits: 1967-1969 firebird

New reproduction includes lock ring & gasket. applications: 1976-1981 Camaro

includes lock ring & gasket. 3/8 in. with 3 outlets.fits: 1978-88 cutlassfits: 1978-87 lemans-grand am-grand prixfits: 1978-83 malibufits: 1978-88 monte carlofits: 1978-88 regal & grand national

includes lock ring & gasket. 3/8 in. with 2 outlets. applications: 1978-1988 cutlass 1978-1987 lemans-grand am-grand prix 1978-1983 malibu 1978-1988 monte carlo 1978-1988 regal & grand national

fits: 1956-1957 chevy 9 passenger station wagon

applications: 1955-1959 chevy & gmc pickup (2nd series)